Contents
Architect scales have numbers that run incrementally both from left to right and from right to left. A whole number or fraction to the left or right of the number line indicates the scale those numbers represent. Engineer scales have numbers that run incrementally from left to right.
What does the title block generally contain?
The title block of a drawing, usually located on the bottom or lower right hand corner, contains all the information necessary to identify the drawing and to verify its validity.
What are engineered plans for motors?
engineered plans for motors, pumps, piping systems, and piping equipment. This means that the drawing gives approximate positions and sizes. These are schematic drawings which show all the equipment, piplines, valves, instruments, and controls needed to operate a piping system.
What is one difference between an engineer’s scale and an architectural scale quizlet?
Terms in this set (8)
Engineer scales are only read from left to right where architect scales can be read from left to right and right to left. Whereas an architect’s scale uses fractional scaling.
What is civil engineering scale?
Civil engineer scales are used to design large projects such as roads, bridges and water mains. Depending on the project, 1 inch on the scale can represent 100 feet in real life. The civil engineer’s scale divides 1 inch into equal decimal units of 10, 20, 30, 40, 50, 60 and 80.
How are architectural and engineering scales divided?
The scale is divided into decimalized fractions of an inch. The six faces of the prism have the following dimensional ratios 1:10, 1:20, 1:30, 1:40, 1:50 and 1:60 unless otherwise stated. The first graduation on an engineer scale is the zero mark.
What is a title block in engineering?
Title block has the highest concentration of information in a sheet of engineering drawing. It is the door to understanding the drawing and the company, and includes all the information which enables the drawing to be intepreted, identified and archived.
What is the size of title block?
The size of the title block is 185 mm x 65 mm which is recommended by BIS (Bureau of Indian Standards).
How do you make a title box in engineering drawing?
How to make a title box In engineering drawing, Title box in …
Which of the following is a typical scale used for floor plans?
Floor plans are most commonly (though not always) drawn on a 1/4” scale, which means a quarter-inch on the plan equals 1 foot of actual length on the completed structure. Some scales use metric instead of imperial measurements.
What defines a key plan?
A small-scale plan of a building or building group which indicates the placement of the principal elements of the scheme.
What is a civil plan?
Civil Plans (also known as “Construction Plans”) are submitted following approval of a Preliminary Plat and prior to or concurrently with submitting a Final Plat (which includes replats, amending plats, and minor plats).
What are engineered plans for motors pumps pumping systems and piping equipment called?
Core Module 5: Construction Drawings Vocabulary
A | B |
---|---|
mechanical plan | plans for motors, pumps, piping systems and piping equipment |
civil plan | used for work that has to do with construction in or on the earth |
structural plan | support the architectural plan give details on the materials to be used |
When the metric system is used dimensions are written in?
When the metric system is used, dimensions are written in: Meters, centimeters, and millimeters.
What are engineered plans for motors pumps piping systems and equipment are called?
mechanical plans. are engineered plans for motors, pumps, piping systems, and piping equipment.
What scales are on an engineering scale?
Referred to as 1:10, 1:20, 1:30,1:40, 1:50 or 1:60 scale. Typically in civil engineering applications, 1:10 (1″=10′) is used exclusively for detail drawings. 1:20 and 1:40 scales are used for working plans. 1:60 is normally used only to show large areas of a project.
What is a scale in engineering drawing?
Definition. A scale is defined as the ratio of the linear dimensions of the object as represented in a drawing to the actual dimensions of the same.
Is scale a ratio?
A scale is a specific type of ratio. It compares a unit on a map or plan or on a scaled model to an actual distance on a map or the size of a real object.
Why are scale ratios used in engineering drawing?
There is a need to reduce or enlarge while drawing the objects on paper. Some objects can be drawn to their actual size. The proportion by which the drawing of aan object is enlarged or reduced is called the scale of the drawing.
What is a scale in architecture?
Scale in architecture is measuring or ratio based on the relation of architectural elements with each other and their surroundings along with being in harmony with human body geometry.
What are the scales on an architectural scale?
Common scales for a triangular architect’s scale are: 16 (full), 3, 1-1/2, 1, 3/4, 1/2, 3/8, 1/4, 1/16, 1/8, 3/32. Major divisions of each scale represent feet which are further subdivided into 12ths or 16ths.
What is the size of engineering drawing sheet?
Drawing Size Reference Table, Architectural and Engineering Drawing Sizes
Standard US Engineering Drawing Sizes | ||
---|---|---|
Drawing Size | Dimensions (millimeters) | Dimensions (inches) |
ANSI A | 215.9 x 279.4 | 8.5 x 11 |
ANSI B | 279.4 x 431.8 | 11 x 17 |
ANSI C | 431.8 x 558.8 | 17 x 22 |
What is reducing scale in engineering drawing?
So when a drawing is prepared smaller than the actual size of the object, the scale used is termed as reducing scale and the drawing is known as a reduced-sized drawing.
What is layout of drawing sheet?
LAYOUT OF DRAWING SHEET:
After selecting the size of the drawing sheet and to divide the proper space for margin, title block, parts list, revision panel, folding marks and selecting a suitable scale on the drawing sheet is known as layout of drawing sheet.
Which of the following is reducing scale Mcq?
Which of the following scales is a reducing scale? Explanation: The representative fraction 1:3 indicates that the dimension of the drawing is one-third of the actual object. Since the drawing is smaller than the actual object, this type of scale is called a reducing scale.
What is technical drawing?
A technical drawing, also known as an engineering drawing, is a detailed, precise diagram or plan that conveys information about how an object functions or is constructed. Engineers, electricians, and contractors all use these drawings as guides when constructing or repairing objects and buildings.
What is title block format?
You can customize title block formats in the standard drawing templates or you can create your own title block formats. A title block includes information about the drawing, the sheet, and the design properties
it updates to display current information.
How many types of lines are there in engineering drawing?
For general engineering drawings, the types of lines recommended by the Bureau of Indian Standards shown in table 2 must be used. The thickness of the lines must be chosen according to the type and size of the drawing from any of the six groups given in Table 1.
What is an assembly drawing?
A drawing which displays the parts of a machine or a machine unit assembled in their relative working positions is known as assembly drawing.
What is lettering in technical drawing?
Technical lettering is the process of forming letters, numerals, and other characters in technical drawing. It is used to describe, or provide detailed specifications for, an object.